Big Solutions for a small planet

Home » SDS

SDS

IONOGRAPH 75/25% TEST FLUID

HEALTH & SAFETY DATA SHEET.
Identification of the Substance/Preparation and Company.
SURCLEAN IONOGRAPH 75/25% TEST FLUID
Company: Surclean Main and Emergency Tel No: +44 (01983) 290333
Unit 1, SMT Technology Centre, Fax No: +44 (01983) 295499
Cowes, Isle of Wight, U.K. P031 7AD.
Composition/Information on Ingredients
General description: a mixture of solvent and purified water for use as a test fluid in Ionograph
test systems used Electronics Manufacturing operations.
Hazardous & non haz. ingredients
Name of Ingredient Concentration UN Number Haz.phrase
Isopropanol Alcohol 75% 1219 Flammab H226
D.I. Water remainder — N/A
Hazards Identification
-Odour: Slight Alcohol odour
-Appearance: Colourless liquid
-Contact with skin: Prolonged skin contact will result in defatting of the skin, irritation, and possible
dermatitus.
-Inhalation: Irritating to eyes and respiratory system (836/37. May cause dizziness, confusion, headache or
stupor).
First aid measures
Contact with skin
-wash the affected area with plenty of soap and water.
-afterwards, a suitable moisturising skin cream can be applied.
Contact with eyes
-If material has got into eyes, wash out immediately with plenty of water for at least 15 minutes.
-Seek medical attention if any irritation persists.
Ingestion
-Give patient plenty of water to drink. NEVER MAKE AN UNCONCIOUS PERSON VOMIT OR
DRINK FLUIDS. DO NOT INDUCE VOMITING.
-Seek medical attention immediately.
Inhalation and General
-Remove the patient from source of exposure to fresh air and lie down. Seek medical advice if neccesary. If
casualty is unconcious, place into the recovery position. Perform artificial respiration if breathing has stopped. If
breathing is difficult, properly trained personnel may assist affected person by administering 100% Oxygen. Keep
affected person warm and at rest. Seek prompt medical attention.
Fire fighting measures
Extinguishing Media
-in case of fire use water spray or fog, alcohol resistant foam, dry chemical or C02 (S43), Sand, Dolomite etc.
Special Fire Fighting Procedures
-Do not use water jets. Wear breathing apparatus. Use Water to keep fire exposed containers cool and to
disperse vapours. Dike for water control. Cool containers exposed to flames with water until well after the fire is out. Move
container from the fire area if it can be done without risk. Use water spray to reduce vapours. For large scale fires in cargo
areas, use unmanned hose holder or monitor nozzles if possible. If not, withdraw and let fire bum out. If risk of water
pollution occurs, notify appropriate authorities.
Exposure hazards
-None known
Accidental release measures
Immediate actions
-Shut off all ignition sources. Avoid sparks, flames, heat and smoking. Ventilate.
Clean up procedures
-Provide ventilation and confine spill. Do not allow runoff to sewer. Absorb spillage in a suitable inert material
such as vermiculite, dry sand or earth and place into appropriate container. Avoid contact with skin or inhalation of
spillage, dust or vapour. Clean up personnel should use respiratory and liquid contact safety protection clothing.
Handling and Storage
Usage precautions
-Keep away from sources of ignition. Avoid spilling, skin and eye contact. Ventilate well, avoid breathing vapours.
Use approved respirator if air contamination is above accepted level. Wear full protective clothing for aged exposure
and/or high concentrations.
Storage Precations
-Low risk flammability/combustibility-keep away from oxidizers, heat and Names. Isolate from other materials.
Keep in a cool, dry, ventilated stage and dosed containers. Ground container and transfer equipment to eliminate static
sparks risk.
Storage Criteria
-Chemical storage.
Exposure Qntrols and Personnel Protection
Normal good room ventilation should be sufficient. Gloves and eye protection are recommended for prolonged or
repeated exposure.
Protective Equipment
Ventilation
-provide adequate general and local exhaust ventilation.
Respirators
-No specific recommendation made, but respiratory protection must be used if the general
level exceeds the Occupational Exposure Level (OEL).
Protective Gloves
-Use protective Gloves. Chloroprene, Nitrile or Butyl Rubber Industrial grade Gloves.
Eye protection
-Wear approved safety goggles. Full face shield protecttion preferred.
Other Protection
-Wear appropriate clothing to prevent any possibility of liquid contact and repeated or
prolonged vapour contact.
Hygenic Work routines
-DO NOT SMOKE IN WORK AREA. Wash at the end of each work period and before
food consumption, smoking or using the toilet. Remove any clothing that becomes
contaminated immediately. Do not eat or drink whilst working with this material.
Physical and Chemical Properties
Appearance
-colourless liquid
Odour/Taste
-Mild. Alcohol. Sweet.
Solubility Description
-Soluble in water.
Changes of state Value/range unit method
Boiling point/range 88 deg C.
Flash Point 49 deg C. Pensky Martens C.Cup.
Auto ignition temperature 425 deg C.
Explosion hazard
Explosion limits
-lower 3.4 % -upper 18%
Vapour pressure
-58Pa @ 20 deg. C.
Density
-0.826 – 0.892 @ 20 deg. C.
Solubilitymiscible
PH Value
-Neutral
viscosity
-3.1 mPas @ 20 deg. C.
Stability and Reactivity
Stability
-Avoid: heat, sparks, moisture and flames.
Materials to avoid
-Bases, Alkalies (Inorganic), Strong Oxidizing agents, Strong Reducing agents
Hazardous Decomposition products
-Material does not decompose up to the specified boiling point. Thereafter in case of fire, material can
create Vapours/gases/Fumes of: Carbon Monoxide (CO), Carbon Dioxide (C02).
Toxicological Information
Toxic Dose-LD50
-ingestion: No data is available for oral toxicity. The values of the ingredients are higher than LD50
(oral rat) : 2000mg/kg.
Skin Contact
-Repeated/prolonged contact causes degreasing, irritation and possible dermatitus.
Eye Contact
-Initial eye contact will cause chronic eye irritation. Inhalation -Higher concentrations can cause
irritation of the respiratory system, nausea and dizziness.
Ecological Information
Mobility
-Dissolves in water. Product remaining on surface evaporates within one day. Larger volumes may
penetrate soil layer and could contaminate groundwater.
Bio-Accumulation
Does not significantly bio-accumulate.
Degradability
-Material is readily bio-degradable meeting the 10 day window crriterion. Oxidizes rapidly by
photochemical reactions in air. This together with its very high flash point means it can be treated as a very
low VOC potential material. Integrated environmental half-life is estimated to be 1-< 10 days.
Acute Fish Toxicity
-Practically non toxic. However best practice states material must not be drained.
Disposal Considerations
Disposal methods UK
-Dipose of in accordance with Local Authority requirements.
EEC waste listing class according to (94/3/EG)
-Disposal No. 140303 (Solvents/Solvent blends not containing Halogenated material)
Suggested disposal/recovery meths
Filtration waste should be collected and disposed of by licensed Chemical waste removal Contractors.
Specification of minor waste content will be mostly that of the production materials for which the
cleaning material was used. To advise the disposal contractor therefore, refer to the production
material data source.
Transport Information
Ground Transportation ADR/RID
-ADR/RID Class 3 Alcohols, n.o.s. (Cont. I.P.A.)
-item 31 C
-UN number 1987 (Limited quantities flammables class)
-UN number 1219 (Quantities above limited class)
Sea Transportation IMDG – Code
-IMGD Classification 3.3 Alcohols, n.o.s. (Cont. I.P.A.)
-page 3303
-UN number 1987 (Limited quantities flammables class)
-UN number 1219 (Quantities above limited class
-Packaging class III
-EMS number 3 – 06
-MFAG 305
Air Transportation ICAO-TI and IATA-DGR
-ICAO/IATA Classification 3 Alcohols, n.o.s. (Cont. I.P.A.)
-UN ID number 1987 Packaging instructions – 309 / 60 I
-Packaging Class 111 – 309 / 10 I
-UN ID number 1219 Packaging instruc tions -10 / 220 1 (Cargo Aircraft only)
EEC/GHS Supply Label- Red Diamond with Flame mark. Legend – Flammable liquid
Hazard Phrases
-H302/312/332 Acute toxicity if swallowed – group 4
-H226 – flammable liquid mixture.
Safety Phrases
-S-24/25 Avoid contact with skin and eyes.
-S36/37 Wear suitable protective clothing and gloves.
Statutary Instruments
-Chemicals (Hazard Information and Packaging) regulations.
-Control of Substances Hazardous to Health (CoSHH) regulations.
Guidance Notes
-Occupational Exposure Limits HSE publication No. EH40.
-GHS harmonzed hazard warning label regulations 2015.
– EU CLP updated (EC) No 1272/2008 + 2012 update.
Issued on 20/01/2021. Issue revision 09.
Disclaimer
This information relates only to the specific material designated and will not be valid for such material used in
combination with any other material or in any process. Such information is, to the best of the Manufacturers
knowledge and belief, accurate and reliable as of the date shown. However, no warranty, guarantee or
representation is made as to its accuracy, reliability or completeness. It is the users sole responsibility to
satisfy himself as to the suitability of such information for their particular application.

Brightflow 210 MSDS

Safety Data Sheet
Surclean Brightflow 210 Universal Solder Flux
Page 1
1. Product Identification
Product Code Surclean Brightflow 210 Flux
Trade Name None
Manufacturer Surclean Electronic Production Materials, Unit 1, SMT Technology Centre,
Prospect Road, Cowes, Isle of Wight, PO31 7AD, United Kingdom.
Supplier / Importer
24 hour Emergency Contact (UK) +44 (0) 1983 290333
2. Composition and information on Components
Hazardous Components Content EC No CAS Hazard Risk
Propan-2-OL <90% 200-746-9 67-63-0 F: Highly Flammable H225
Xn :Irritant H320. H315 H334
Remainder Not classified
3. Hazard Identification
Main Hazards Highly Flammable
Irritating to eyes, respiratory system and skin. Eye Irritation – Cat 2A Skin – Cat 2
Health Effects Inhalation – Ingestion Inhalation of the fumes or ingestion may cause headache, nausea, muscular pain.
Irritation of the eyes and nose may result from contact with soldering fumes.
Chronic (Prolonged effects) Anaemia, insomnia, weakness, constipation, nausea and abdominal pain due to
ingestion. Skin rash, damage of mucous membrane due to skin exposure and
inhalation.
4. First Aid Measures
First Aid – Eyes Immediately flush the eyes with water for at least 15 minutes, holding the eye open.
Obtain medical attention urgently.
First Aid – Skin Wash thoroughly with soap and water and remove all contaminated clothing as
washing proceeds. Apply suitable lotion to prevent dryness. Seek medical
attention.
First Aid – Inhalation Remove person to fresh air and keep subject warm and at rest. Seek medical
attention.
First Aid – Ingestion Wash out mouth with water. Do not induce vomiting. Keep subject warm and at
rest. Seek medical attention.
Not Classified
Safety Data Sheet
Brightflow 210
Page 2
5. Fire Fighting Measures
Extinguishing media Use Carbon Dioxide, Dry chemical, Alcohol resistant foam. Beware of the
possibility of re-ignition.
Special Hazards Dangerous when exposed to heat of flame. Containers may explode in heat of fire.
Vapours can travel a considerable distance to source of ignition to cause flashback.
Protective Equipment for Fire Fighting Wear full protective clothing and use breathing apparatus.
6. Accidental Release Measures
Personal Precautions Wear appropriate protective clothing. Eliminate sources of ignition. Vapour is
heavier than air and will collect in basements etc.. Avoid breathing vapour.
Precaution. statements – Eyes P305+351+338. Inhallation P304+341 Skin P302+P352
Environmental Precautions Try to prevent the product entering drains or water courses.
Spillages Small spillages can be flushed with large volumes of water. Larger spillages should
be collected for disposal. Beware of vapour collecting to form explosive
concentrations. Allow to evaporate if it is safe to do so or contain using absorbent
material such as earth, sand or other inert material.
7. Handling and Storage
Handling Use in well ventilated area. Avoid breathing in vapour, mist or resultant soldering
fumes. Avoid contact with eyes, skin and clothing. Keep container tightly closed.
Larger containers (20l) are heavy. Take care when lifting and pouring.
Storage Storage area should be well ventilated, cool and dry. Store in original containers.
Re package only if container becomes damaged. Store away from sources of heat
or ignition.
8. Exposure Controls – Personal Protection
Occupational Exposure Limits TLV OSHA PEL ACGHIH TLV
Propan-2-OL 400ppm 400ppm 400ppm
Engineering Control Measures Ensure work area is well ventilated and equipment exhausted. If pouring is needed
then this should be arrange so as not expose the operator to unnecessary vapour
levels.
Respiratory Protection Respiratory protection if there is a risk of exposure to high vapour levels.
Hand protection Nitrile rubber gloves or PVC gloves should be used when handling or pouring
Eye Protection Close fitting Chemical goggles should be worn when handling or pouring.
Skin Protection Normal work wear but rubber apron if there is a danger of splashing or spillage.
Foot Protection Wear protective boots or toe caps when handling drums.
Safety Data Sheet
Page 3
9. Physical and Chemical Properties
Appearance light straw liquid
Odour Ethereal Odour
Acid Number 24 +/- 1.0
Boiling point 82 Deg C @ 760mm Hg
Melting point n/a
Flash Point 16 Deg C
Auto Ignition Temperature 456 Deg C
Flammability limits in air Lower : 2.5 %
Upper : 12 %
Explosion Limits Lower : 2.5 %
Upper : 12 %
Vapour pressure 33.0 mm Hg at 50 Deg C
Vapour Density 2.07 (Air = 1)
Evaporation Rate <2.3 (BuAc = 1)
Specific Gravity 0.820 +/- 0.006 (H2O = 1 @ 25 Deg C)
Solubility Partially soluble in water
10. Stability and Reactivity
Stability Stable under normal conditions
Conditions to avoid High temperature – sources of ignition
Materials to avoid Strong oxidising agents
Hazardous Decomposition Products May release toxic vapours / gases such as Carbon Monoxide, Carbon Dioxide
11. Toxicological Information
Basis of Assessment Information given is based on product data
Acute Toxicity – Oral LD50 > 2000 mg/kg
Acute Toxicity – Dermal LD50 > 2000 mg/kg
Acute Toxicity – Inhalation LD50 > 5mg/L
Eye Irritation Slight irritant
Skin Irritation Slight Irritant
Respiratory Irritation Irritant in animal studies
Skin sensitisation May cause skin sensitisation
(Sub) Chronic Toxicity Repeated exposure causes liver damage
Human effects Repeated exposure can lead to allergic contact dermatitis. High exposure can
cause drowsiness and dizziness. Can cause liver damage There may be other
health risks but these will vary from person to person.
12. Ecological Information
Mobility The product will readily dissolve in water
Degradability The product is readily Biodegradable
Bio-accumulation Not expected to accumulate
Ecotoxicity Poses a significant risk of oxygen depletion in aquatic systems
13. Disposal
Product Incineration recommended. Material is classifies as special waste under the COPA
regulations 1980 and must be disposed of in accordance with those regulations.
Containers Leave labels in tact until containers have been thoroughly cleaned. Empty containers may contain hazardous
residues and vapours. Dispose of containers with care
Brightflow 210
Safety Data Sheet
Page 4
14. Transport Information
UN Number, Shipping name and Class 1993 Flammable Liquid NOS
Proper Shipping Name Contains Isopropanol
UN Class / Packing Group 3 / II
Packing Symbol Flammable Liquid
Trim Card Number Brightflow 210
15. Regulatory Information
Labelling Information Highly Flammable Irritant Environmental
Risk Phrases H225 :Highly Flammable
H320,315,334:Irritating to eyes, respiratory system and skin
Safety Phrases S7 :Keep container tightly closed
S16 :Keep away from sources of ignition – No Smoking
S24 :Avoid contact with skin
S23 :Do not breath fumes or spray
S26 :In case of contact with eyes, rinse immediately with plenty of water
and seek medical advice.
S62 : If swallowed, do not induce vomiting: seek medical advice immediately
and show this container or label.
EC Annex 1 Classification F: Highly Flammable
Xi Irritant
Regulations / References Refer to the requirements of all relevant local regulations. For the United Kingdom,
see Control of Substances Hazardous to Health Regulations (COSHH), the Health
and Safety at Work Act (HSWA) and the Carriage of Dangerous Goods by Road
and Rail Regulations 1994. GHS (EU) Regulations. Contains no substances of V.H.C
16. Other Information
Application See technical data sheet for application information
06/2018 Rev. 4.0

Brightflow 210 TDS

SMT
SURFACE MOUNT TECHNOLOGY
SMT Technology Centre,
Prospect Road, Cowes, Isle of Wight,
United Kingdom, PO31 7AD.
Tel:+44 (0)1983 290333 Fax:+44 (0)1983 295499
Web Site-http:/www.surclean.co.uk.
email: info@surclean.co.uk
Technical Process data – Brightflow 210LF Flux
Brightflow 210LF is a Halide free low solids organic Flux for high temperature lead free wave soldering
on both surface mount and through hole applications. It is suitable for all common alloys, and gives
superior wetting with bright solder joints. It conforms to all no clean class requirements, and does not
degrade by reduction of surface insulation resistance on soldered assemblies. If required, Brightflow 210LF
can be cleaned, in localized areas by Hydrocarbon solvents, or by offline cleaning in Aqueous chemistries,
preferably with buffered Alkali Saponification and typically a PH of 11, and heated to @ 60 deg. C.
Flux Classification Data
Specification Test standard
Flux Class ORL0 IPC-J-STD-004B
Colour & Appearance Clear Liquid
Copper Mirror Pass IPC-TM-650 2.3.32
SIR 2.1312 x 10 Ohms IPC-TM-650 2.6.3.3
Specific Gravity (g/cm3) 0.811 + 0.006
Solids Content % VW 3.0 + 0.5
Acid Number (mgKOH/g) 40.0 – 50.0 By Titration
Process Control
Spray flux application method
If the flux is applied by spray method, flux monitoring and control is not required as it is a total loss system
and is constantly replenished with as manufactured specification flux.
Foam flux application method
If the flux application is by the older bubble foam type applicator, repeatable and accurate flux deposition on the PCB will require monitoring and control of the flux. Because this flux is a very low solids content type, traditional specific gravity measurement is not accurate enough for the assessment of solids %, and testing for the total acid number by Titration, and adjustment with Isosolve thinners is the recommended method for maintenance of the correct flux concentration. Foam type fluxer units will require periodic removal of debris and other contaminants from the reservoir, and replacement of the flux. It is recommended that this is done
every 30 – 40 hours of soldering operation.
Process Methods
For production wave soldering of HASL or bare copper PCB boards, 210LF can be applied by spray or foam
fluxer systems. Foam type fluxers should be supplied with dry oil free air, and the flux reservoir should be
kept topped up. Flux surface should be 25 – 30 mm above the foamer stone/aerator. In either application
method, an air knife can be beneficial in removing excess flux, though with the spray method, adjustment for
consistant coating is more finely and easily achieved by time and pressure adjustment. Uniformity of the spray flux coating can be assessed by running a tempered glass test plate throught the spray fluxer and
preheat zones, and then visually inspecting prior to transit into the solder wave zone.
Typical Process Parameters
Parameter Typical Parameter Level
Amount of Flux Spray application: 750 – 1500 ug/in2 solids
Amount of Flux Foam application: 1000 – 2000 ug/in2 solids
Foam Fluxer Parameters:
Foam Stone Pore Size 20 – 50 um.
Flux Level Above Stone 25 – 35 mm
Vent opening 10 – 13 mm
Inlet Air Pressure 1 – 2 P.S.I.
Top Side Preheat Temperature 85 – 110 deg. C.
Bottom Side Preheat Temperature Selected Top Side Temperature + 35 deg. C.
Conveyer Speed (depends on length) Typical Range 1200 – 1800 mm per minute.
Contact Time in Solder Wave 2.5 – 4.5 Seconds
Solder Pot Temperatures (by alloy)
Sn 96.5 / Ag 3.5 260 – 276 deg. C
Sn 95 / Ag 5 280 – 296 deg. C.
Sn 99.3 / Cu 0.7 265 – 276 deg. C.
Sn / Ag / Cu 271 – 276 deg. C.
Sn 95 / Sb 5 280 – 296 deg. C.
SN100C (Nihon Superior) 260 – 275 deg. C.
Storage and Shelf Life
210LF should be stored in the supply container within a cool dry environment, and held within the
temperature range 18 – 26 deg. C. Shelf life is two years from date of manufacture.
Disposal
210LF contains some hazardous ingredients, and if required to be disposed of, must be done
so in accordance with local and national regulations within the country of use.
Data sheet : V1.1 20/09/2020.

IONOGRAPH 99/1 IPA TOP UP FLUID

HEALTH & SAFETY DATA SHEET.
Identification of the Substance/Preparation and Company.
IONOGRAPH 99/1 IPA TOP UP FLUID
Company: SMT-Surclean Main and Emergency Tel No: +44 (01983) 290333
SMT Technology Centre, Prospect Rd., Fax No: +44 (01983) 295499
Cowes, Isle of Wight, U.K. P031 7AD.
Composition/Information on Ingredients
General description: a mixture of solvent and water for the removal of residues in Electronics
Ionograph test systems.
Hazardous ingredients
Name of Ingredient Concentration CAS number Hazard phrases
Isopropanol Alcohol 99.7% 67-63-0 H225, H315, H319,H335, H336
Water remainder — N/A
Hazards Identification
-Odour: Slight fragrence
-Appearance: Colourless liquid
-Contact with skin: Prolonged skin contact will result in defatting of the skin, irritation, and possible
dermatitus, H315.
-Inhalation: Irritating to eyes and respiratory system (H319, H335. May cause dizziness, confusion,
headache or stupor, H336.
-Highly Flammable, H225.
First aid measures
Contact with skin
-wash the affected area with plenty of soap and water.
-afterwards, a suitable moisturising skin cream can be applied.
Contact with eyes
-If material has got into eyes, wash out immediately with plenty of water for at least 15 minutes.
-Seek medical attention if any irritation persists.
Ingestion
-Give patient plenty of water to drink. NEVER MAKE AN UNCONCIOUS PERSON VOMIT OR
DRINK FLUIDS. DO NOT INDUCE VOMITING.
-Seek medical attention immediately.
Inhalation and General
-Remove patient from source of exposure to fresh air & lie down. Seek medical advice if neccesary. If casualty
is unconcious, place into recovery position. Perform artificial respiration if breathing has stopped. If breathing is difficult,
trained personnel may assist by administering 100% Oxygen. Keep warm and at rest. Seek prompt medical attention.
Fire fighting measures
Extinguishing Media
-in case of fire use water spray or fog, alcohol resistant foam, dry chemical or C02 (S43), Sand, Dolomite etc.
Special Fire Fighting Procedures
-Do not use water jets. Wear breathing apparatus. Use Water to keep fire exposed containers cool and to
disperse vapours. Dike for water control. Cool containers exposed to flames with water until well after the fire is out. Move
container from the fire area if it can be done without risk. Use water spray to reduce vapours. For large scale fires in cargo
areas, use unmanned hose holder or monitor nozzles if possible. If not, withdraw and let fire bum out. If risk of water
pollution occurs, notify appropriate authorities.
Exposure hazards
-None known
Accidental release measures
Immediate actions
-Shut off all ignition sources. Avoid sparks, flames, heat and smoking. Ventilate.
Clean up procedures
-Provide ventilation and confine spill. Do not allow runoff to sewer. Absorb spillage in a suitable inert material
such as vermiculite, dry sand or earth and place into appropriate container. Avoid contact with skin or inhalation of
spillage, dust or vapour. Clean up personnel should use respiratory and liquid contact safety protection clothing.
Handling and Storage
Usage precautions
-Keep away from sources of ignition. Avoid spilling, skin and eye contact. Ventilate well, avoid breathing vapours.
Use approved respirator if air contamination is above accepted level. Wear full protective clothing for aged exposure
and/or high concentrations.
Storage Precations
-Low risk flammability/combustibility-keep away from oxidizers, heat and Names. Isolate from other materials.
Keep in a cool, dry, ventilated stage and dosed containers. Ground container and transfer equipment to eliminate static
sparks risk.
Storage Criteria
-Chemical storage.
Exposure Controls and Personnel Protection
Normal good room ventilation should be sufficient. Gloves and eye protection are recommended for prolonged or
repeated exposure.
Protective Equipment
Ventilation
-provide adequate general and local exhaust ventilation.
Respirators
-No specific recommendation made, but respiratory protection must be used if the general
level exceeds the Occupational Exposure Level (OEL).
Protective Gloves
-Use protective Gloves. Chloroprene, Nitrile or Butyl Rubber Industrial grade Gloves.
Eye protection
-Wear approved safety goggles. Full face shield protecttion preferred.
Other Protection
-Wear appropriate clothing to prevent any possibility of liquid contact and repeated or
prolonged vapour contact.
Hygenic Work routines
-DO NOT SMOKE IN WORK AREA. Wash at the end of each work period and before
food consumption, smoking or using the toilet. Remove any clothing that becomes
contaminated immediately. Do not eat or drink whilst working with this material.
Physical and Chemical Properties
Appearance
-colourless liquid
Odour/Taste
-Mild. Alcohol. Sweet.
Solubility Description
-Soluble in water.
Changes of state Value/range unit method
Boiling point/range 82 deg C.
Flash Point 12 deg C. Pensky Martens C.Cup.
Auto ignition temperature 425 deg C.
Explosion hazard
Explosion limits
-lower 2 % -upper 13.4 %
Vapour pressure
-43.2 hPa @ 20 deg. C.
Density
-0.785 – 0.892 @ 20 deg. C.
Solubilitymiscible
PH Value
-Neutral
viscosity
-3.1 mPas @ 20 deg. C.
Stability and Reactivity
Stability
-Avoid: heat, sparks, moisture and flames.
Materials to avoid
-Bases, Alkalies (Inorganic), Strong Oxidizing agents, Strong Reducing agents
Hazardous Decomposition products
-Material does not decompose up to the specified boiling point. Thereafter in case of fire, material can
create Vapours/gases/Fumes of: Carbon Monoxide (CO), Carbon Dioxide (C02).
Toxicological Information
Toxic Dose-LD50
-ingestion: No data is available for oral toxicity. The values of the ingredients are higher than LD50
(oral rat) : 5045mg/kg.
Skin Contact
-Repeated/prolonged contact causes degreasing, irritation and possible dermatitus.
Eye Contact
-Initial eye contact will cause chronic eye irritation. Inhalation -Higher concentrations can cause
irritation of the respiratory system, nausea and dizziness.
Ecological Information
Mobility
-Dissolves in water. Product remaining on surface evaporates within one day. Larger volumes may
penetrate soil layer and could contaminate groundwater.
Bio-Accumulation
Does not significantly bio-accumulate.
Degradability
-Material is readily bio-degradable meeting the 10 day window crriterion. Oxidizes rapidly by
photochemical reactions in air. This together with its very high flash point means it can be treated as a very
low VOC potential material. Integrated environmental half-life is estimated to be 1-< 10 days.
Acute Fish Toxicity LC50 test 9640 mg/l 96 hours (ref. US EPA).
-Practically non toxic. However best practice states material must not be drained.
Disposal Considerations
Disposal methods UK
-Dipose of in accordance with Local Authority requirements.
EEC waste listing class according to (94/3/EG). Dispose of in accordance with 2008/98EC.
-Disposal No. 140303 (Solvents/Solvent blends not containing Halogenated material)
Suggested disposal/recovery meths
Filtration waste should be collected and disposed of by licensed Chemical waste removal Contractors.
Specification of minor waste content will be mostly that of the production materials for which the
cleaning material was used. To advise the disposal contractor therefore, refer to the production
material data source.
Transport Information
Ground Transportation ADR/RID
-ADR/RID Class 3 Alcohols, n.o.s. (Cont. I.P.A.)
-item 31 C
-UN number 1219
Sea Transportation IMDG – Code
-IMGD Classification 3.3 Alcohols, n.o.s. (Cont. I.P.A.)
-page 3303
-UN number 1219
-Packaging class III
-EMS number 3 – 06
-MFAG 305
Air Transportation ICAO-TI and IATA-DGR
-ICAO/IATA Classification 3 Alcohols, n.o.s. (Cont. I.P.A.)
-UN ID number 1219 Packaging instructions – 309 / 60 I
-Packaging Class 111 – 309 / 10 I
-10 / 220 1 (Cargo Aircraft only)
Regulatory Information
EEC Supply Label GHS- WARNING – FLAMMABLE LIQUID & VAPOUR
DANGER
Hazard Phrases
-H319,Harmful by inhalation, in contact with skin/eyes, and if swallowed.
-H335 Irritating to respiratory system.
-H336 May cause drowsiness or dizziness if inhaled.
-H225 Highly flammable liquid and vapour.
Precautionary Statements
-P210 keep away from heat,sparks, open flame and other ignition sources. Do not smoke.
-P305, P351, P338 IF IN EYES Rinse with water for several minutes. Remove any contact lenses
if present, then continue rinsing with water.
-P370, P378 IN CASE OF FIRE Use dry powder extinguisher or sand to extinguish.
-P403, P235 Store in a well ventilated place, out of direct sunlight. Keep cool.
Issue date and revision number
Issued on 29/02/2021. Issue revision 10.
Disclaimer
This information relates only to the specific material designated and will not be valid for such material used in
combination with any other material or in any process. Such information is, to the best of the Manufacturers
knowledge and belief, accurate and reliable as of the date shown. However, no warranty, guarantee or
representation is made as to its accuracy, reliability or completeness. It is the users sole responsibility to
satisfy himself as to the suitability of such information for their particular application.

Shopping Cart
Scroll to Top